Evaluation of Titanium Alloy Surface Roughness After Phosphoric Acid Etching
DOI:
https://doi.org/10.30659/odj.12.3.280-291Keywords:
Dental implant, acid etching, titanium alloy, surface roughnessAbstract
ABSTRACT
Background: Tooth loss can be caused by periodontal disease, caries, and other factors. Dental implants made of titanium are a common solution to replace tooth loss. Titanium grade 5 (Ti-6Al-4V) is often chosen for an implant. Modern commercial implant surface roughness (Ra) ranges from 1 to 2 μm. Surface roughness has an important role in osseointegration. The acid etching method can be used to improve surface roughness. This study evaluates titanium alloy surface roughness after etching with varying concentrations of H3PO4 acid.
Method: A laboratory experiment with a pre-test and post-test group design. 25 titanium alloy samples were divided into 5 groups (n=5) and treated with saline, HCl 37%, and H3PO4 acid 38%, 48%, and 58%. Surface roughness was measured using a surface roughness tester, while EDS and SEM tests analyzed titanium composition and surface characteristics.
Result: The titanium used in this study is a titanium alloy. Surface roughness modification using acid had a higher roughness compare to saline with significant different (p<0.05). Surface roughness in the group H3PO4 48% and 58% had a lower roughness compared to HCl 37% but no significant different (p>0.05). Referring to the SEM results, each acid showed morphological changes on the surface and for saline there were no morphological changes.
Conclusion: Varying concentrations of H3PO4 acid can effectively improve the surface roughness of titanium alloys, with solutions at 48% and 58% demonstrating similar effectiveness to 37% HCl acid.
References
Berglundh T, Giannobile WV, Lang NP, Sanz M, Lindhe J, editors. Anatomy and Histology of Periodontal Tissues. Clinical Periodontology and Inmplant Dentistry. 7th ed. Vol. 1. Hoboken, NJ Chichester: Wiley Blackwell; 2022. 3–5 p.
Fiorellini JP, Kim D, Chang YC. Anatomy, Structure, and Function of The Periodontium in Newman & Carranza's Clinical Periodontology. Newman MG. Takei HH, Klokkevold PR, Carranza FA (editors). 13th ed. Philadelphia:Elsevier. p.19 - 20.
Kinane DF, Stathopoulou PG, Papapanou PN. Periodontal diseases. Nat Rev Dis Primer. 2017 Jun 22; 3:1–2. doi: 10.1038/nrdp.2017.38
Tim Riset Kesehatan Dasar 2018 (Indonesia), Indonesia, editors. Laporan nasional Riskesdas 2018. Jakarta: Kementerian Kesehatan, Republik Indonesia, Badan Penelitian dan Pengembangan Kesehatan; 2019. 628 p.
Wahyuni LA, Nurilawaty V, Widiyastuti R, Purnama T. Pengetahuan Tentang Penyebab dan Dampak Kehilangan Gigi Terhadap Kejadian Kehilangan Gigi Pada Lansia. JDHT J Dent Hyg Ther. 2021 Oct 4;2(2):52–7. doi: 10.36082/jdht.v2i2.335
Anshary MF, Cholil, Arya IW. Gambaran Pola Kehilangan Gigi Sebagian Pada Masyarakat Desa Guntung Ujung Kabupaten Banjar. Dentino Jur Ked Gigi. 2014;2(2):138–43.
Rizkillah MN, Isnaeni RS, Fadilah RPN. Pengaruh kehilangan gigi posterior terhadap kualitas hidup pada kelompok usia 45-65 tahun. Padjadjaran J Dent Res Stud. 2019;3(1):8.
Wahjuni S, Mandanie SA. Fabrication of combined Prosthesis with Castable Extracoronal Attachments (Laboratory Procedure). J Vocat Health Stud. 2017;1(2):75–81. doi: https://doi.org/10.20473/jvhs.V1.I2.2017.75-81
Prawesthi E, Pramono DH. Buku Ajar Gigi Tiruan Cekat Mahkota Metal Porselen (PFM). In Poltekkes Kemenkes Jakarta II; 2019. p. 1–6. Available from: https://perpus.poltekkesjkt2.ac.id/respoy/index.php?p=show_detail&id=4605&keywords=
Natarajan M, Pasupuleti T, Giri J, Sunheriya N, Katta LN, Chadge R, et al. Machinability of Titanium Grade 5 Alloy for Wire Electrical Discharge Machining Using a Hybrid Learning Algorithm. Information. 2023 Aug 3;14(8):439. doi: 10.3390/info14080439
Jayesh R, Dhinakarsamy V. Osseointegration. J Pharm Bioallied Sci. 2015;7(5):226. doi: 10.4103/0975-7406.155917
França FL, Botelho A do CF, Araújo FGS. Phosphoric Acid Increases the Porosity and Extends the Contact Area of Dental Osseo integrated Implants. Int J Adv Eng Res Sci. 2018;5(3):230–6. doi: 10.22161/ijaers.5.3.30
Diab Al-Radha DrAS. The influence of different acids etch on dental implants titanium surface. IOSR J Dent Med Sci. 2016 Aug;15(08):87–91. doi: 10.9790/0853-1508098791
Von Wilmowsky C, Moest T, Nkenke E, Stelzle F, Schlegel KA. Implants in bone: Part I. A current overview about tissue response, surface modifications and future perspectives. Oral Maxillofac Surg. 2014 Sep;18(3):243–57. doi: 10.1007/s10006-013-0398-1
Nicolas-Silvente AI, Velasco-Ortega E, Ortiz-Garcia I, Monsalve-Guil L, Gil J, Jimenez-Guerra A. Influence of the Titanium Implant Surface Treatment on the Surface Roughness and Chemical Composition. Materials. 2020 Jan 9;13(2):314. doi: 10.3390/ma13020314
Gad SC. Phosphoric acid. In: Reference Module in Biomedical Sciences [Internet]. Elsevier; 2023 [cited 2023 May 26]. p. B9780128243152008137. Available from: https://linkinghub.elsevier.com/retrieve/pii/B9780128243152008137
B. Demir, Bedeloğlu E, Koyuncuoğlu CZ. The Effect of Slow Speed Drilling on The Stability of Dental Implants During Osseointegration: A Clinical Study. J Osseointegration. 2023;15(2):91. doi: 10.23805/JO.2023.542
Fitriani CY, Wibawa A. Biokompatibilitas Material Titanium Implan Gigi. Insisiva Dent J Maj Kedokt Gigi Insisiva [Internet]. 2019 [cited 2023 May 4];8(2). Available from: https://journal.umy.ac.id/index.php/di/article/view/7834
Damisih D, Jujur IN, Sah J, Prajitno DH. Effect of Heat Treatment Temprature on Microstructure Characteristic and Hardness Properties of Casted Ti-6Al-4V ELI. Widyariset. 2018 Nov 30;4(2):156. doi: 10.14203/widyariset.4.2.2018.153-162
Zakaria MY, Ramli MI, Sulong AB, Muhamad N, Ismail MH. Application of sodium chloride as space holder for powder injection molding of alloy Titanium–Hydroxyapatite composites. J Mater Res Technol. 2021 May; 12:478–86. doi: 10.1016/j.jmrt.2021.02.087
Speight JG. Environmental inorganic chemistry for engineers. Kidlington, Oxford, United Kingdom: Butterworth-Heinemann is an imprint of Elsevier; 2017. 580 p.
Wang G, Li J, Lv K, Zhang W, Ding X, Yang G, et al. Surface thermal oxidation on titanium implants to enhance osteogenic activity and in vivo osseointegration. Sci Rep. 2016 Aug 22;6(1):31769. doi: 10.1038/srep31769
El-Sayed AR, Mohamed AE, Hassan FSM, El-Mahdy MS. Influence of Titanium Additions to Aluminum on the Microhardness Value and Electrochemical Behavior of Synthesized Aluminum-Titanium Alloy in Solutions of HCl and H3PO4. J Mater Eng Perform. 2023 Feb;32(4):1760–77. doi: 10.1007/s11665-022-07248-8
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:
Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
This work is licensed under a Creative Commons Attribution 4.0 International License.
